|
|
HEMCO offers a complete line of Laboratory Fume Hoods, including bench-mounted hoods in widths from 24 to 96 inches and floor-mounted (walk-in) hoods from 48 to 144 inches wide and up to 96 inches deep. Hemco UniFlow hoods are constant volume low flow designed for performance and energy savings. HEMCO UniFlow Fume Hoods are designed and manufactured to conform and perform to industry recommendations and standards.
Betatek offers complete services and systems to complete your UniFlow Fume Hood installation, such as service fixtures for gases and liquids, plumbing, electrical services, work surfaces, sinks, base cabinets, ventilation ducting, HEPA and carbon filters, monitors and exhaust blowers to meet your exact application requirements.
 |
UniFlow SE Fume HoodsUniFlow SE Fume Hood is designed for high efficiency, energy savings and maximum user protection. The aerodynamic face opening with airfoil provides uniform airflow through the fume chamber. A constant volume low flow hood with VaraFlow baffle system efficiently directs the airflow through the fume chamber to the bell shaped exhaust outlet with minimum turbulence and maximum user protection. Click HERE for more information. |
 |
UniFlow LE Fume HoodsThe UniFlow LE Fume Hoods are low flow constant volume for high efficiency energy saving and maximum user protection. The aerodynamic face opening with airfoil provides uniform airflow into the fume chamber. Available in sizes 48 inches, 60 inches, 72 inches and 96 inches wide x 48 inches height x 32 inches depth. Click HERE for more information. |
 |
UniFlow CE Fume HoodsThese models are a low flow constant volume, LCV type fume hood that requires no VAV controls, no motorized baffles, no costly auxiliary air system and no special integral supply fans. These units can save 50% or more in costly exhaust volume typically required to operate a conventional fume hood. The CE series accomplishes this superior containment performance through engineering and manufacturing features incorporated into the HEMCO line of Uniflow Laboratory Fume Hoods. Click HERE for more information. |
 |
UniFlow FM Fume HoodsThe Air By-Pass Walk-In Hood is ideally suited for synthesis, distillation and other rack type operations where tall apparatus is used or equipment is rolled into the work area. In sizes 48", 60", 72" & 96" widths and depths of 30", 36" & 48". The UniFlow Walk-In Hood accommodates laboratory procedures requiring an increased height work area for floor height equipment such as distillation and other rack type operations where tall apparatus is used or when equipment must be rolled into the work area. Click HERE for more information. |
 |
UniFlow Conventional/VAV Fume HoodsThe conventional fume hood maintains constant air volume through sash opening. Equipped with optional VAV system, face velocity can be controlled to meet specific requirements. Click HERE for more information. |
 |
UniFlow Auxiliary-Air Fume HoodsThe Auxiliary-Air Fume Hood reduces the loss of expensive tempered air from the laboratory. Ideal for laboratories with inadequate make-up air supply. Auxiliary-Air Fume Hoods come in 48", 60", 72" and 96" widths. A supply air solution for many labs that have insufficient room airflow. Equipped with auxiliary air plenum to induce added airflow to face opening of hood. Supply air ducting and remote blower is required. Equipped with vapor proof-light and switch. All electrical components and services are UL and CSA listed. Optional hood accessories and hood ventilation systems are available. Click HERE for more information. |
 |
UniFlow Clean Aire I Fume HoodsThe UniFlow Clean Aire I Hoods are available in 48", 60", 72" and 96" models incorporated with filtration systems to control exhaust emissions. UniFlow Clean Aire Hoods feature a factory installed filter housing that can be equipped with either HEPA and/or carbon filters to help meet environmental concerns and regulations according to the Clean Air Act. Contaminants are then filtered prior to exhausting to the outside, therefore reducing pollution and avoiding the risk of contaminants re-entering the building through the air supply system. Since the filter housing is located on the fume hood, monitoring and maintaining the filters is convenient. Carbon and HEPA filters are available to suit your specific particulate or gas/vapor removal requirements. Click HERE for more information. |
 |
UniFlow Perchloric Acid and PVC Acid Digestion Fume HoodsPerchloric Acid and Acid Digestion Hoods feature a stainless steel or PVC liner and a convenient wash down system for the safe handling of acids. UniFlow Stainless Steel Perchloric Acid Bypass Hoods are designed specifically for Perchloric Acid use. UniFlow PVC Perchloric Acid Bypass and Acid Digestion Hoods feature fume chamber and baffle constructed of type 1 PVC liner with 24" interior depth. Click HERE for more information. |
 |
UniFlow Radioisotope Fume HoodsThe UniFlow Radioisotope Fume Hood is available in 48", 60" and 72" widths. Interior is constructed of Type 304 Stainless Steel to prevent absorption of radioactive and corrosive mate- rials. Click HERE for more information. |
 |
UniFlow Dual Entry Fume HoodsDual Entry Air By-Pass Hoods are ideal for demonstrations or applications where observation and access is required from both sides of the fume hood. Dual Entry Fume Hoods are available in 48", 60", 72" and 96" wide models in either 30" or 48" depths. They can be positioned on an island or peninsular locations. Dual Entry hoods can also be located on a common wall of two rooms with accessibility from either room. Click HERE for more information. |